OpenRFC.org Requests For Comments ... for the community
Welcome to OpenRFC
Home Full RFC index RFC humour Our technology
 
<< Previous <<      RFC 4813      >> Next >>    
OSPF Link-Local Signaling.
B. Friedman, L. Nguyen, A. Roy, D. Yeung, A. Zinin. March 2007.

 
[Direct link][Download PDF version][Download text version]
 

Network Working Group B. Friedman Request for Comments: 4813 L. Nguyen Category: Experimental A. Roy D. Yeung Cisco Systems A. Zinin Alcatel February 2007 OSPF Link-Local Signaling Status of This Memo This memo defines an Experimental Protocol for the Internet community. It does not specify an Internet standard of any kind. Discussion and suggestions for improvement are requested. Distribution of this memo is unlimited. Copyright Notice Copyright (C) The IETF Trust (2007). Abstract OSPF is a link-state intra-domain routing protocol used in IP networks. OSPF routers exchange information on a link using packets that follow a well-defined format. The format of OSPF packets is not flexible enough to enable applications to exchange arbitrary data, which may be necessary in certain situations. This memo describes a vendor-specific, backward-compatible technique to perform link-local signaling, i.e., exchange arbitrary data on a link. Friedman, et al. Experimental [Page 1]
RFC 4813 OSPF Link-Local Signaling February 2007 Table of Contents 1. Introduction ....................................................2 2. Proposed Solution ...............................................2 2.1. Options Field ..............................................3 2.2. LLS Data Block .............................................4 2.3. LLS TLVs ...................................................5 2.4. Predefined TLV .............................................5 2.4.1. Extended Options TLV ................................5 2.4.2. Cryptographic Authentication TLV ....................6 3. Backward Compatibility ..........................................7 4. Security Considerations .........................................7 5. IANA Considerations .............................................7 6. References ......................................................8 6.1. Normative References .......................................8 6.2. Informative References .....................................8 Appendix A. Acknowledgements ......................................9 1. Introduction Formats of OSPF [RFC2328] packets are not very flexible to provide an acceptable mechanism for opaque data transfer. However, this appears to be very useful to allow OSPF routers to do so. An example where such a technique could be used is exchanging some capabilities on a link (standard OSPF utilizes the Options field in Hello and Exchange packets, but there are not so many bits left in it). One potential way of solving this task could be introducing a new packet type. However, that would mean introducing extra packets on the network, which may not be desirable, so this document describes how to exchange data using existing, standard OSPF packet types. 2. Proposed Solution To perform link-local signaling (LLS), OSPF routers add a special data block at the end of OSPF packets or right after the authentication data block when cryptographic authentication is used. Like with OSPF cryptographic authentication, the length of the LLS- block is not included into the length of OSPF packet, but is included in the IP packet length. Figure 1 illustrates how the LLS data block is attached. Friedman, et al. Experimental [Page 2]
RFC 4813 OSPF Link-Local Signaling February 2007 +---------------------+ -- | IP Header | ^ | Length = HL+X+Y+Z | | Header Length | | v +---------------------+ -- | OSPF Header | ^ | Length = X | | |.....................| | X | | | | OSPF Data | | | | v +---------------------+ -- | | ^ | Authentication Data | | Y | | v +---------------------+ -- | | ^ | LLS Data | | Z | | v +---------------------+ -- Figure 1: Attaching LLS Data Block The LLS data block may be attached to OSPF packets of two types -- type 1 (OSPF Hello), and type 2 (OSPF DBD). The data included in the LLS block attached to a Hello packet may be used for dynamic signaling, since Hello packets may be sent at any moment in time. However, delivery of LLS data in Hello packets is not guaranteed. The data sent with Database Description (DBD) packets is guaranteed to be delivered as part of the adjacency forming process. This memo does not specify how the data transmitted by the LLS mechanism should be interpreted by OSPF routers. The interface between the OSPF LLS component and its clients is implementation- specific. 2.1. Options Field A new bit, called L (L stands for LLS), is introduced to the OSPF Options field (see Figure 2). The value of the bit is 0x10. Routers set the L-bit in Hello and DBD packets to indicate that the packet contains the LLS data block. Friedman, et al. Experimental [Page 3]
RFC 4813 OSPF Link-Local Signaling February 2007 +---+---+---+---+---+---+---+---+ | * | O | DC| L |N/P| MC| E | * | +---+---+---+---+---+---+---+-+-+ Figure 2: The Options Field L-bit This bit is set only in Hello and DBD packets. It is not set in OSPF Link State Advertisements (LSAs) and may be used in them for different purposes. 2.2. LLS Data Block The data block used for link-local signaling is formatted as described below (see Figure 3 for illustration). 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Checksum | LLS Data Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | | LLS TLVs | . . . . . . +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 3: Format of the LLS Data Block Checksum The Checksum field contains the standard IP checksum of the entire contents of the LLS block. LLS Length The 16-bit LLS Data Length field contains the length (in 32-bit words) of the LLS block including the header and payload. Implementations should not use the Length field in the IP packet header to determine the length of the LLS data block. Note that if the OSPF packet is cryptographically authenticated, the LLS data block must also be cryptographically authenticated. In this case, the regular LLS checksum is not calculated and the LLS block will contain a cryptographic authentication TLV (see Section 2.4.2). Friedman, et al. Experimental [Page 4]
RFC 4813 OSPF Link-Local Signaling February 2007 The rest of the block contains a set of Type/Length/Value (TLV) triplets as described in Section 2.3. All TLVs must be 32-bit aligned (with padding if necessary). 2.3. LLS TLVs The contents of the LLS data block is constructed using TLVs. See Figure 4 for the TLV format. The Type field contains the TLV ID that is unique for each type of TLVs. The Length field contains the length of the Value field (in bytes) that is variable and contains arbitrary data. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | . . . Value . . . +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 4: Format of LLS TLVs Note that TLVs are always padded to 32-bit boundary, but padding bytes are not included in the TLV Length field (though it is included in the LLS Data Length field of the LLS block header). 2.4. Predefined TLV 2.4.1. Extended Options TLV This subsection describes a TLV called Extended Options (EO) TLV. The format of EO-TLV is shown in Figure 5. Bits in the Value field do not have any semantics from the point of view of the LLS mechanism. This field may be used to announce some OSPF capabilities that are link-specific. Also, other OSPF extensions may allocate bits in the bit vector to perform boolean link-local signaling. The length of the Value field in EO-TLV is 4 bytes. The value of the Type field in EO-TLV is 1. EO-TLV should only appear once in the LLS data block. Friedman, et al. Experimental [Page 5]
RFC 4813 OSPF Link-Local Signaling February 2007 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | 1 | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Extended Options | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 5: Format of EO-TLV Currently, [RFC4811] and [RFC4812] use bits in the Extended Options field of the EO-TLV. The Extended Options bits are also defined in Section 5. 2.4.2. Cryptographic Authentication TLV This document defines a special TLV that is used for cryptographic authentication (CA-TLV) of the LLS data block. This TLV should be included in the LLS block when the cryptographic (MD5) authentication is enabled on the corresponding interface. The message digest of the LLS block should be calculated using the same key as that used for the main OSPF packet. The cryptographic sequence number is included in the TLV and must be the same as the one in the main OSPF packet for the LLS block to be considered authentic. The TLV is constructed as shown Figure 6. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | 2 | AuthLen | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Sequence Number | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | . . . AuthData . . . +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 6: Format of Cryptographic Authentication TLV The value of the Type field for CA-TLV is 2. The Length field in the header contains the length of the data portion of the TLV that includes 4 bytes for the sequence number and the length of the message digest (MD5) block for the whole LLS block Friedman, et al. Experimental [Page 6]
RFC 4813 OSPF Link-Local Signaling February 2007 in bytes (this will always be 16 bytes for MD5). So the AuthLen field will have value of 20. The Sequence Number field contains the cryptographic sequence number that is used to prevent simple replay attacks. For the LLS block to be considered authentic, the sequence number in the CA-TLV must match the sequence number in the OSPF packet. The AuthData field contains the message digest calculated for the LLS data block. The CA-TLV may appear in the LLS block only once. Also, when present, this TLV should be the last in the LLS block. 3. Backward Compatibility The modifications to OSPF packet formats are compatible with standard OSPF because LLS-incapable routers will not consider the extra data after the packet; i.e., the LLS data block will be ignored by routers that do not support the LLS extension. 4. Security Considerations The function described in this document does not create any new security issues for the OSPF protocol. The described technique provides the same level of security as the OSPF protocol by allowing LLS data to be authenticated (see Section 2.4.2 for more details). 5. IANA Considerations LLS TLV types are maintained by the IANA. Extensions to OSPF that require a new LLS TLV type must be reviewed by a designated expert from the routing area. Following the policies outlined in [RFC2434], LLS type values in the range of 0-32767 are allocated through an IETF consensus action, and LLS type values in the range of 32768-65536 are reserved for private and experimental use. This document assigns LLS types 1 and 2, as follows: LLS Type Name Reference 0 Reserved 1 Extended Options [RFC4813] 2 Cryptographic Authentication [RFC4813] 3-32767 Reserved for assignment by the IANA 32768-65535 Private Use Friedman, et al. Experimental [Page 7]
RFC 4813 OSPF Link-Local Signaling February 2007 This document also assigns the following bits for the Extended Options bits field in the EO-TLV outlined in Section 2.4.1: Extended Options Bit Name Reference 0x00000001 LSDB Resynchronization (LR) [RFC4811] 0x00000002 Restart Signal (RS-bit) [RFC4812] Other Extended Options bits will be allocated through an IETF consensus action. 6. References 6.1. Normative References [RFC2328] Moy, J., "OSPF Version 2", STD 54, RFC 2328, April 1998. [RFC2434] Narten, T. and H. Alvestrand, "Guidelines for Writing an IANA Considerations Section in RFCs", BCP 26, RFC 2434, October 1998. 6.2. Informative References [RFC4811] Nguyen, L., Roy, A., and A. Zinin, "OSPF Out-of-Band Link State Database (LSDB) Resynchronization", RFC 4811, February 2007. [RFC4812] Nguyen, L., Roy, A., and A. Zinin, "OSPF Restart Signaling", RFC 4812, February 2007. Friedman, et al. Experimental [Page 8]
RFC 4813 OSPF Link-Local Signaling February 2007 Appendix A. Acknowledgments The authors would like to acknowledge Russ White for his review of this document. Authors' Addresses Barry Friedman Cisco Systems 225 West Tasman Drive San Jose, CA 95134 USA EMail: friedman@cisco.com Liem Nguyen Cisco Systems 225 West Tasman Drive San Jose, CA 95134 USA EMail: lhnguyen@cisco.com Abhay Roy Cisco Systems 225 West Tasman Drive San Jose, CA 95134 USA EMail: akr@cisco.com Derek Yeung Cisco Systems 225 West Tasman Drive San Jose, CA 95134 USA EMail: myeung@cisco.com Alex Zinin Alcatel Sunnyvale, CA USA EMail: zinin@psg.com Friedman, et al. Experimental [Page 9]
RFC 4813 OSPF Link-Local Signaling February 2007 Full Copyright Statement Copyright (C) The IETF Trust (2007). This document is subject to the rights, licenses and restrictions contained in BCP 78, and except as set forth therein, the authors retain all their rights. This document and the information contained herein are provided on an "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY, THE IETF TRUST AND THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Intellectual Property The IETF takes no position regarding the validity or scope of any Intellectual Property Rights or other rights that might be claimed to pertain to the implementation or use of the technology described in this document or the extent to which any license under such rights might or might not be available; nor does it represent that it has made any independent effort to identify any such rights. Information on the procedures with respect to rights in RFC documents can be found in BCP 78 and BCP 79. Copies of IPR disclosures made to the IETF Secretariat and any assurances of licenses to be made available, or the result of an attempt made to obtain a general license or permission for the use of such proprietary rights by implementers or users of this specification can be obtained from the IETF on-line IPR repository at http://www.ietf.org/ipr. The IETF invites any interested party to bring to its attention any copyrights, patents or patent applications, or other proprietary rights that may cover technology that may be required to implement this standard. Please address the information to the IETF at ietf-ipr@ietf.org. Acknowledgement Funding for the RFC Editor function is currently provided by the Internet Society. Friedman, et al. Experimental [Page 10]

   

[Home] [Full RFC index] [RFC humour] [Our technology]

Copyright © Inter-Corporate Computer & Network Services, Inc.  All rights reserved.
All trademarks and RFC contents are the property of their respective owners.